NanoPaint: A Tool for Rapid and Dynamic Imaging of Membrane Structural Plasticity at the Nanoscale

Single‐particle tracking with quantum dots (QDs) constitutes a powerful tool to track the nanoscopic dynamics of individual cell membrane components unveiling their membrane diffusion characteristics. Here, the nano‐resolved population dynamics of QDs is exploited to reconstruct the topography and structural changes of the cell membrane surface with high temporal and spatial resolution. For this proof‐of‐concept study, bright, small, and stable biofunctional QD nanoconstructs are utilized recognizing the endogenous neuronal cannabinoid receptor 1, a highly expressed and fast‐diffusing membrane protein, together with a commercial point‐localization microscope. Rapid QD diffusion on the axonal plasma membrane of cultured hippocampal neurons allows precise reconstruction of the membrane surface in less than 1 min with a spatial resolution of tens of nanometers. Access of the QD nanoconstructs to the synaptic cleft enables rapid 3D topological reconstruction of the entire presynaptic component. Successful reconstruction of membrane nano‐topology and deformation at the second time‐scale is also demonstrated for HEK293 cell filopodia and axons. Named “nanoPaint,” this super‐resolution imaging technique amenable to any endogenous transmembrane target represents a versatile platform to rapidly and accurately reconstruct the cell membrane nano‐topography, thereby enabling the study of the rapid dynamic phenomena involved in neuronal membrane plasticity.     

硅酸盐型胶磷矿单一反浮选工艺研究及工业化应用

云南某矿区产的硅酸盐型胶磷矿的SiO_2含量一般在30%以上,堆存数量巨大,使用常规的单一反浮选工艺难以达到要求的精矿指标,但是使用正反浮选工艺或者双反浮选工艺的生产成本又较高,经济效益不理想。从矿石的多元素分析发现,与CaO∶P_2O_5大于1.79的碳酸型磷块岩配矿后使用单反浮选工艺可以获得合格的精矿指标。在此思路上,对两种矿石进行配合比、解离度、磨矿细度和药剂制度的探索研究。当配合比为1∶3,磨矿细度为92%,药剂制度为抑制剂1.5kg/t、调整剂18kg/t、捕收剂3.0kg/t的情况下,最终可以获得P_2O_5品位为28.89%,MgO品位为0.91%,产率62.73%,回收率85.24%的精矿指标。     

湿法氧化锌种类和用量对天然橡胶性能的影响

研究湿法氧化锌种类和用量对天然橡胶(NR)性能的影响。结果表明:与添加普通氧化锌的胶料相比,对于未填充炭黑NR体系,减半用量的湿法氧化锌混炼胶的焦烧时间和t90较短,Fmax较大;硫化胶的定伸应力、拉伸强度和剪切模量(G′)较大,拉断伸长率、损耗模量(G″)和损耗因子(tanδ)较小。对于填充炭黑NR体系,减半用量的湿法氧化锌混炼胶的门尼粘度、G′和G″较大,tanδ较小,焦烧时间和t90较短,Fmax较大;硫化胶的密度稍低,硬度和定伸应力较大,耐老化性能较好,玻璃化温度较低,tanδ较小,其他物理性能变化不大。湿法氧化锌FF的性能优于湿法氧化锌HR。     

流量伺服阀作压力控制的非典型应用

文章提出并分析了一种用力反馈式流量伺服阀与手动节流阀配合使用,从而对负载进行压力控制的液压桥路。该桥路本质为C型半桥:伺服阀单腔输出,节流阀通过调节回油液阻来调节负载腔压力的起始点,伺服阀根据负载需求改变流量输出。整个压力控制回路为纯机械式控制,稳定可靠,精度可达0.1 bar。     

新型卡板式外径千分表的设计应用

针对机车牵引电机转轴磨削测量中,对转轴轴承位尺寸超差的原因进行分析,设计制作机车牵引电机转轴新型卡板式外径千分表(实用新型:ZL201420477030.7)。实际应用表明,新型卡板式外径千分表保证了牵引电机转轴轴承位的磨削尺寸,避免了转轴轴承位尺寸超差现象,解决了机车牵引电机转轴轴承位磨削测量的工艺、质量问题。     

Extensive evaluation and classification of low-cost dust sensors in laboratory using a newly developed test method

An extensive evaluation of low-cost dust sensors was performed using an exponentially decaying particle concentration. A total of 264 sensors including 27 sensors with light-emitting diodes (LEDs) and 237 sensors with laser lighting sources were tested. Those tested sensors were classified into 4 groups based on the deviation from the reference data obtained by a reference instrument. The response linearities of all the tested samples for PM₁, PM_2.5, and PM₁₀ were in excellent agreement with the reference instrument, except a few samples. For the measurements of PM₁ and PM_2.5, the lighting source, that is, LED or laser, did not show any significant difference in overall sensor performance. However, LED-based sensors did not perform well for PM₁₀ measurements. The 32, 24, and 16% of all the tested sensors for PM₁, PM_2.5, and PM₁₀ measurement, respectively, are in the category of Class 1 (reference instrument reading ± 20%) requirement. The performance of the low-cost dust sensors for PM₁₀ measurement was relatively less satisfactory.     

盐溶液种类和浓度对α-半水脱硫石膏合成的影响

为了解决脱硫石膏的大量堆存对环境造成的潜在危害,同时提高脱硫石膏的附加值,采用常压盐溶液水热法以电厂脱硫石膏为原料探究α-半水石膏的最佳合成工艺,重点研究了盐溶液种类及浓度对α-半水石膏的合成过程、合成产物组成及结构的影响。结果表明：在氯化钙、氯化镁盐溶液中,由于同离子效应和硫酸镁离子对的形成,导致半水石膏的形成过程受阻。较高浓度氯化钾和氯化钠盐溶液可使二水石膏发生转晶,其中氯化钾会致使半水石膏过度脱水生成无水钾石膏,氯化钠盐溶液可以使二水石膏转变为半水石膏并维持较长时间,通过比较得出最佳合成工艺为氯化钠溶液质量分数为15%、体系反应温度为95 ℃、固液质量比为1∶4、搅拌速率为150 r/min、合成时间为3 h,可以制得长径比约为5∶1的六方短柱状α-半水石膏。     

延长油田X油区长8储层孔隙结构特征研究

根据岩心、薄片及压汞资料,系统分析了长8储层的孔隙结构特征,并将其分为4种类型,其中Ⅰ类孔隙类型为优质储层。